Loren Data's SAM Daily™

SAMDAILY.US - ISSUE OF JUNE 15, 2025 SAM #8602
SOLICITATION NOTICE

42 -- Cascade System

Notice Date

6/13/2025 10:59:23 AM
 

Notice Type

Combined Synopsis/Solicitation
 

NAICS

333912 — Air and Gas Compressor Manufacturing
 

Contracting Office

W7NH USPFO ACTIVITY MS ARNG FLOWOOD MS 39232-8861 USA
 

ZIP Code

39232-8861
 

Solicitation Number

W9127Q25QA009
 

Response Due

6/24/2025 8:00:00 AM
 

Archive Date

07/09/2025
 

Point of Contact

Reggie Clark, Phone: 6013131565, Laurie C. Morris, Phone: 6013131663
 

E-Mail Address

reginald.m.clark.civ@army.mil, laurie.c.morris3.civ@army.mil
(reginald.m.clark.civ@army.mil, laurie.c.morris3.civ@army.mil)
 

Small Business Set-Aside

SBA Total Small Business Set-Aside (FAR 19.5)
 

Description

***********Update, Amendment************* The purpose of this Amendment is to extend the closing date to 24 June 2025 update technical requirements. Question deadline has also been extended to 17 June 2025. This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in the Federal Acquisition Regulation (FAR) Subpart 12.6, as a supplemented additional information in the notice. This announcement constitutes the only solicitation; quotes are being requested, and a written solicitation will not be issued. Solicitation number W9127Q25QA009 is being issued as a Request for Quotation (RFQ) with Open Market Pricing. This solicitation document, incorporated provisions, and clauses are those in effect through Federal Acquisition Circular (FAC) FAC 2024-05, Effective April 22, 2024, and the Defense Federal Acquisition Regulation (DFARS) Publication Notice (DPN) dated January 17, 2025. This requirement is a small business set aside under NAICS 333912 with a size standard of 1000 Employees. The MSARNG has a requirement for Cascade System (SCBA Air Compressor/Fill Station). See Salient Characteristics for the full scope of work. CLIN 0001: Cascade Air Compressor System General Requirements Must be able to fill at least three SCBA Bottles at the simultaneously. Fill SCBA bottles to pressure of minimum 4750PSI. Must have a minimum of four 6000psi Fill Bank tanks. Must have Digital Carbon monoxide and Water monitoring. Noise shall not exceed 76 DB at one meter. Must have automatic shutoff and drain capabilities. Must include Freight/shipping, Installation, and Training. Must include the country of origin. Must include Factory warranty consisting of at least the following; Manufactured compressors, compressor systems and accessory equipment are warrantied for eighteen (18) months from date of shipment or twelve (12) months from the date of start-up, whichever occurs first. Compressor pumps installed as an integral part of compressors or compressor systems are warrantied for a total of twenty-four (24) months, from the date of shipment. Replacement and service parts are warrantied for ninety (90) days from the date of shipment. Replacement compressor pumps are warrantied for one-hundred eighty (180) days from the date of shipment. Factory repairs are warrantied for ninety (90) days from the date of shipment. Option to purchase 5yr/1000hr (whichever occurs first) warranty Further Technical requirements I. General Arrangement The breathing air compressor shall be a packaged appliance designed to deliver high pressure breathing air in compliance with the most current NFPA and CGA air quality standards for the refilling of SCBA and SCUBA cylinders. The system shall include the high pressure air compressor, electric motor, air purifier, and all operating controls as specified below. The breathing air compressor shall be completely assembled and tested by the manufacturer requiring only electrical power supply to operate. The breathing air compressor shall be designed with all operating controls and performance indicators located on a panel at the front of the appliance allowing �at sight� operator monitoring. The appliance shall comply with the currently applicable OSHA specifications as well as state and local electrical codes. The external construction of the high pressure breathing air compressor shall be appliance-like. All structural fasteners shall be concealed and all access panels shall include concealed hinges and push button latches. Two (2) full height doors on each side of the appliance shall be provided for maintenance access to the compressor. The doors shall include a shutdown switch to prevent exposure to running gear in the event either is opened while the compressor is in operation. The cabinet shall be designed to minimize noise emission and include sound abatement insulation. The noise level shall not exceed 76 dB at one meter. The compressor control panel shall be ergonomically designed and feature graphic design technology to group all control components and indicators logically and by function. For maximum clarity and visibility, colored lines shall isolate each control component group. Each group shall then be located within a graphic flow control schematic background and identified with permanent text integral to the panel surfaces. High visibility colored text shall identify and provide operator instructions for all critical functions. The cabinet configuration shall permit installation with the rear �against the wall� and dimensions not to exceed 71�H x 34-��W x 41�D. A removable blister panel in the rear will allow for a doorway clearance of 34�, if required. The appliance shall include an ambient air flow control design that directs the necessary volume of cooling air to the compressor. The cooling system shall also include an integral, top discharge extractor to completely vent the resulting hot air from the compression process out of the cabinet. All high pressure air plumbing shall be rated for 6000 psig working pressure and utilize seamless stainless steel tubing. All high pressure air tube connections shall use compression type fittings. The electrical control system shall include motor control components with UL, NEMA or IEC approval and 12vdc control circuit housed within a UL� listed, NEMA enclosure. The breathing air system manufacturer shall be a NRTL (Nationally Recognized Testing Laboratory) Licensed Panel Shop as per UL� 508A standard. II. Compressor The ambient air intake and compression shall be through an air-cooled, reciprocating, pressure oil lubricated, four-stage compressor designed for continuous duty at 6000 psig working pressure with a charging rate of 14.0 CFM. The air compressor design shall include a heavy-duty cast iron crankcase supporting the crankshaft with oversized ball bearings on each end. The cylinder arrangement shall be a balanced �V� configuration featuring ringed pistons assuring maximum balance and air volume delivery efficiency while operating at a maximum compressor speed of 1500 RPM. Lubrication shall be accomplished by controlled splash and shall include a crankshaft driven oil pump to supply metered quantities of oil directly to the fourth stage piston through a replaceable (spin-off) full flow filter. Crankcase level is verified via an oil level sight glass with minimum and maximum indicators. Each stage of compression shall be protected with a safety relief valve. Valve inspection covers are provide for the first and second stage cylinders to allow for easy access. All valve assemblies shall be designed so they can be repaired without replacing the entire assembly. The cylinders shall include cooling fins to dissipate heat into the cooling air flow from the compressor�s integral flywheel fan. Individually mounted coolers shall be located after each compression stage to cool the discharged air to 18�F. above ambient temperature. Accumulated condensation from cooling the compressed air shall be collected in moisture separators mounted on each stage of the compressor and discharged to an automatic, internal, timed drain system for proper collection and disposal. Prior to shutdowns, the compressor shall be allowed to run unloaded (with opened drains) for a timed period (Purge Cycle) in order to purge all cylinders, separators and crankcase of damaging condensation that develops as compressors cool down. The compressor control panel shall also include a condensate purge test switch in order to verify proper operation of the automatic condensate drain system on demand. The ambient air filter element shall be located in a housing piped to the compressor air intake to draw air from the installation room. Additionally, an inlet port shall be provided with a connection to facilitate connecting to outside air intake piping. III. Electric Motor The compressor shall be v-belt driven by a NEMA design, 10 HP, open drip proof electric motor wired for the electrical conditions as shown below: 60 Hertz Current - 1 Phase, 208/230 volts The motor shall be located under the compressor and driven via v-belt drive arrangement utilizing a hinged motor base to facilitate belt tension adjustment. The compressor and motor base shall include zinc plated, steel encased neoprene mounts to isolate vibration from the appliance. IV. Electrical Control System The breathing air compressor shall include all the necessary controls to assure safe, efficient operation and monitor performance. The control system shall be of an anti-flutter circuit design and include a latched fault protection circuit to prevent automatic restarting after an abnormal fault has occurred. As a minimum, the control system must include the following: � Air pressure switch to automatically start and stop the compressor based on demand. � High air temperature shutdown switch. � Low oil pressure shutdown switch. � Magnetic, across-the-line starter with electric motor overload protection. � Compressor access door safety shutdown switch. � Compressed air AirMonitor system including CO and H2O detectors with pre-set warning, shutdown limits and audible alarm. A shutdown audible alarm shall be supplied for all abnormal conditions. � Auto-drain condensate reservoir capacity shutdown switch with illuminated indicator. V. Instrumentation The control system must include all monitoring devices as indicated below. These shall be mounted on a control panel located at the front of the compressor with all indicators and gauges grouped logically and each group positioned within a graphic flow control schematic and identified with integral text. The panel background color shall be matte black shade with a textured finish to eliminate glare. Panel component and indicator groups shall be offset by colored lines to enhance operational visibility and safety. The compressor�s instrumentation panel shall also be engineered for quick and convenient access to all key electrical control components, minimizing the need to use the appliance maintenance access doors. Indicator lights, pressure switch and all control wiring shall be accessible for routine maintenance and adjustments through hinged, �knockdown� sub-panels on the front of the compressor. The operator control panel shall be designed and pre wired to permit the easy plug and play installation of optional CO or H2O monitor additions. The unit must be designed to allow full integral installation of any future upgrades without the use of external wiring, piping or remotely mounted components. As a minimum, the instrumentation required is as follows: � Compressor inter-stage and final pressure gauges. � Compressor oil pressure gauge. � Hour-meter. � Independent illuminated power ON and OFF buttons. � Normal high air pressure shutdown indicator light. � Purge cycle indicator light and test switch. � Enhanced shutdown indicator light package including low oil pressure, high compressed air temperature, motor overload, auto-drain reservoir limit and door ajar shutdown conditions. � General fault shutdown indicator light. � Emergency stop button. � Digital CO and H2O panel with actual content display in PPM and prompter software keypad for CO monitor calibration. A flow panel with factory plumbed calibration gases shall be included. VI. Air Purification System The high pressure air purification system shall be a multi-chamber arrangement that utilizes disposable cartridges manufactured to provide breathing air that meets or exceeds NFPA and CGA Grade �E� specifications and all other equivalent and recognized standards in use worldwide. All system components shall be rated for 6000 psig working pressure with a four-to-one safety factor. All chambers in the system shall be constructed of 304 stainless steel to enhance safety and corrosion resistance. The purification system shall be sized to process 35,000 cubic feet of air at 70�F and compressed to 6000 psig between cartridge changes. The system shall include the following: � Final separator chamber connected to the automatic condensate drain system. � Check valve to prevent back pressure to the compressor. One (1) 33� purifier cartridge chamber. � Pressure maintaining valve to assure that the system is maintained pressurized in order to attain the rated processing capacity of the air purification cartridge(s). � Safety relief valve. � Drain valve to relieve the system pressure for maintenance. � Stem-mounted gauge for system pressure verification. The system shall be designed so that filling cannot occur in the event that the purification cartridge is not installed. Additionally, the purification system shall have �keyed� chambers so that the filter cartridges can only be installed in their proper sequence. Fill Station I. General Arrangement The fill station shall be designed for filling two (2) or more SCBA cylinders simultaneously or separately. The fill station shall be designed for filling one (1) SCUBA cylinder with a maximum height of 30-�� and a maximum diameter of 7-��, including service valve, boot and fill attachment. The enclosure shall be designed to contain the impact of suddenly expanded high pressure air and all displaced fragments in the unlikely event of a cylinder or fill component rupture. The fill station containment design must be UL� (Underwriters Laboratories) classified and for maximum operator safety certified to meet NFPA 1901-2016 standards. The UL� testing certificate must be included with the bid or request for quotation and included with the operator�s manual when the system is shipped. The fill station loading door must be designed to be trapped behind the fill enclosure cabinet frame when closed and include an automatic, safety interlock to prevent filling unless the loading door is completely closed. A safety relief valve, to prevent over pressurizing SCBA/SCUBA cylinders above 4750 psig for 4500 psig SCBA filling shall also be included. The external construction of the high pressure, breathing air fill station shall be appliancelike. All structural fasteners shall be concealed and all access panels shall include concealed hinges and push button latches. The fill station control panel shall tilt down to allow for convenient maintenance access. The overall dimensions of the fill station including up to four integral air storage cylinders shall not exceed 37-��(W) x 34�(D) x 75�(H). The fill control panel shall be ergonomically designed and feature graphic design technology to group all control components and indicators logically and by function. For maximum clarity and visibility, colored lines shall isolate each control component group. Each group shall then be located within a graphic flow control schematic background and identified with permanent text integral to the panel surfaces. High visibility colored text shall identify and provide operator instructions for all critical functions. The fill station must allow the fill process to be accomplished from the front. The fill station shall be of a design that does not require the operator to have to hold up or otherwise support the weight of the cylinders being filled while connecting them to the fill whips. The front loading door shall be designed so that, when opened, sleeves that hold the SCBA/SCUBA cylinders tilt forward to ease loading and minimize operator fatigue. Two (2) fill whips, each fitted with a cylinder fill adapter and shut-off valve, shall be located within the enclosure. Access Door Control: For maximum operator comfort and ease of use, the fill station access door shall include an air actuator handle designed to provide power assisted, effortless operation when opening and closing. When fully closed, the door shall trip a safety interlock allowing air flow to the fill station. The access door shall be supported on the enclosure frame with an adjustable bearing bushing on each side assuring a balanced and smooth rotation when opening and closing. A damper strut shall secure the assembly to the enclosure so that it does not require operator support and to cushion the access door landing when opened. The access door design must be fail-safe, permitting manual operation in the event of air pressure loss in the power assist circuit. II. Air Flow Controls All air flow components and indicators shall be mounted on a control panel located at the front of the unit grouped logically with each group positioned within a graphic flow control schematic and identified with integral text. The panel background color shall be matte black shade with a textured finish to eliminate glare. Panel component and indicator groups shall be offset by colored lines to enhance operational visibility and safety. For maximum clarity and safety, the flow control panel shall be divided by function, assuring that the regulated SCBA/SCUBA fill controls are located in a dedicated area apart from air storage management components. In order to minimize operator handling of pressurized components, a fill hose(s) pressure vent valve shall be located on the air flow control panel to relieve all fill hoses of pressure after opening the front loading door and before disconnection from the SCBA/SCUBA cylinder(s). The SCBA/SCUBA cylinder fill control system shall include a regulated panel with all the components, devices and piping arrangement necessary to direct supplied compressed high pressure breathing air to the air storage system and the SCBA/SCUBA cylinders being filled. Additionally, a regulated auxiliary outlet to fill remote air storage systems shall be provided. All high pressure regulators must be designed so that they cannot be accidentally reset in accordance with NFPA 1901 standards. The regulator knob shall be of the �push-to-reset� design that spins freely if accidentally moved. A cascade control system shall be included for the number of banks specified below to permit filling or drawing down each air storage cylinder independently of each other and while filling SCBA/SCUBA cylinders. The system shall include a by-pass valve to permit filling SCBA/SCUBA cylinders directly from the compressor. As a minimum, the air control panel must include the following: � Inlet pressure gauge. � Adjustable, 0-6000 psig self-relieving regulator. � Regulated outlet pressure gauge. � By-pass valve. � SCBA/SCUBA cylinder(s) fill control valve. � SCBA/SCUBA cylinder(s) fill pressure gauge. � SCBA/SCUBA cylinder(s) panel mounted fill hose(s) vent valve. � Auxiliary outlet with flow control valve and CGA fitting. � Four (4) bank cascade control with �TO� and �FROM� valves and gauge per bank. III. High Pressure Air Storage The breathing air storage system shall be integral to the appliance and include all the cylinders, plumbing and hardware installed in accordance with all current UN/ISO codes, as specified below: Four (4) UN/ISO 6000 PSI cylinders each with a capacity of 509 cubic feet of air at 6000 psig. The piping of air storage shall be arranged for cascade filling. Delivery to: 138 Military Drive Flowood, MS 39232 Delivery: FOB Destination within 4-6 weeks ARO Basis of Award: The government intends to award a purchase order to the responsible offeror whose quote conforms to the solicitation and is considered to be the most advantageous to the Government in accordance with FAR Part 12, Acquisition of Commercial Items, Evaluation will be in accordance with FAR 13.106 and is based on Best Value to the Government in terms of (i) Technical capability of the item offered to meet the Government requirement; (ii) Price; (iii) Past Performance History. Technical shall be weighted higher than price. To ensure timely and equitable evaluation of quotes, offerors must comply with instructions contained herein. Quotes must be complete, self-sufficient, and respond directly to the requirements of this RFQ. Proposals shall include: (1) Price quote to include itemized description of what is included in the quote (2) detailed specifications and product literature that sufficiently describe the product(s) being offered. (3) Lead time for delivery. Must include pictures. Note: Quotes submitted without detailed product information and/or only restate the government provided specification will not be considered acceptable and shall be removed from further consideration. This notice does not obligate the Government to award the contract; it does not restrict the government's ultimate approach; nor does it obligate the Government to pay for any quote/proposal preparation costs. Only firm fixed price quotes will be evaluated. Along with your quote, please provide the country of origin for the products quoted, the Company Name with CAGE Code, TIN, UEI and Company POC with contact information (email and telephone number). Prompt payment discount terms (i.e. Net 30). SAM is a mandatory requirement for all DoD Government contracts. You must be registered and have an active status in order to be eligible for award of a contract. To register online go to http://www.sam.gov/ It is the contractors' responsibility to be familiar with applicable Clauses and Provisions. Clauses and provisions incorporated by reference may be accessed via https://www.acquisition.gov/. Please see attached listing of Clauses and Provisions. Deadline for receipt of your quote is established for no later than 10:00 A.M. Central Daylight Time (CDT), Tuesday, June 24, 2025. Please email quote to reginald.m.clark.civ@army.mil and laurie.c.morris3.civ@army.mil. All questions concerning this requirement must be submitted by Tuesday, June 17, 2025, at 1:00 PM CDT. Questions will be answered via an amendment to this solicitation. Questions are to be submitted electronically to reginald.m.clark.civ@army.mil and laurie.c.morris3.civ@army.mil. Please ensure the solicitation number ""W9127Q25QA009 - Cascade System"" is included in the subject line of all email correspondence.
 

Web Link

SAM.gov Permalink
(https://sam.gov/opp/4f3da2960409411aa45d12d0ed66d41f/view)
 

Place of Performance

Address: Flowood, MS 39232, USA

Zip Code: 39232

Country: USA
 

Record

SN07477369-F 20250615/250613230049 (samdaily.us)
 

Source

SAM.gov Link to This Notice
(may not be valid after Archive Date)

---

| FSG Index  |  This Issue's Index  |  Today's SAM Daily Index Page |